Posts: 117
Threads: 23
Joined: May 2017
Reputation:
7
Operating system(s):
- Windows (Vista and later)
Gimp version: 2.10
Hello!
Having just upgraded from 2.8.14 to 2.10.6, I have met a surprise (for me) in working with painting tools on layers with wholly transparent pixels:
* under 2.8, choosing mode 'darken only', 'soft light', etc., the brush worked only over the already 'painted' pixels, skipping those with full tansparency--never painted or previously deleted.
* under 2.10.6, the effect on painted pixels is as expected, BUT tansparent pixels get filled as per mode 'normal'.
QUESTION 1: is this effect configurable? i.e., I cannot pretend to understand most of the new features--maybe I am missing something?
QUESTION 2: if it IS a new, unavoidable feature, HOW DO OTHERS FEEL ABOUT IT? I find it
* counter-intuitive: how do you lighten/darken WHAT ISN'T THERE?
* no end of a bore to lock transparency to change the color of a small spot (without bleeding out of the drawing), and then unlock to edit the boundary with transparency. In fact, it is almost as bad as editing a masked layer--endlessly checking/unchecking 'edit mask'.
On the other hand, some features (so far) are fine: loading time, memory load, BLENDING TOOL...
Any suggestions would appreciated. Thanks!
Posts: 243
Threads: 16
Joined: Oct 2016
Reputation:
11
Operating system(s):
- Windows (Vista and later)
On 2.10.6 I did the following:
- open an image (average values of colours)
- add on top a transparent layer
- set mode to darken only
- painted on the transparent layer with a standard black brush : effect=darkened
- changed mode to lighten only : effect=none
Repeated on 2.8.22: got the same results.
Hence, in may case nothing new.
Posts: 7,133
Threads: 155
Joined: Oct 2016
Reputation:
1,004
Operating system(s):
Gimp version: 2.10
09-14-2018, 08:59 AM
(This post was last modified: 09-14-2018, 09:05 AM by rich2005.
Edit Reason: edit
)
Edit: well that was a waste of time, Note to all users, please give accurate descriptions.
Posts: 117
Threads: 23
Joined: May 2017
Reputation:
7
Operating system(s):
- Windows (Vista and later)
Gimp version: 2.10
09-14-2018, 09:00 AM
(This post was last modified: 09-14-2018, 09:10 AM by rich2005.
Edit Reason: remove excess quotes, formatting
)
See my reply to I am editing a layer in 'mode normal' with a brush in mode 'darken only'.
Thanks!
Posts: 7,133
Threads: 155
Joined: Oct 2016
Reputation:
1,004
Operating system(s):
Gimp version: 2.10
(09-14-2018, 09:00 AM)carmen Wrote: See my reply to I am editing a layer in 'mode normal' with a brush in mode 'darken only'.
Thanks!
Change the brush mode to legacy
Posts: 851
Threads: 11
Joined: Oct 2016
Reputation:
89
Operating system(s):
- Windows (Vista and later)
Gimp version: 2.10
(09-14-2018, 09:00 AM)carmen Wrote: See my reply to I am editing a layer in 'mode normal' with a brush in mode 'darken only'.
Switch on the Alpha Lock?
Posts: 6,342
Threads: 274
Joined: Oct 2016
Reputation:
564
Operating system(s):
Gimp version: 2.10
09-14-2018, 09:45 AM
(This post was last modified: 09-14-2018, 09:47 AM by Ofnuts.)
Works for me:
To clear possible misunderstandings:
- On the top layer, you can paint everywhere, the image below doesn't act as a selection mask
- The top layer applies to the composition of all layers below it, not just to the layer below.
- If you want to apply the effect just on the layer below, you use a layer group.
Without a layer group:
With a layer group:
Otherwise, make a screenshot of your layer stack (and indicate the layer modes by renaming the layers)
Posts: 7,133
Threads: 155
Joined: Oct 2016
Reputation:
1,004
Operating system(s):
Gimp version: 2.10
Sorry guys, my fault over enthusiastic editing of everything quoted over a one line reply.
I was peed off after making a comprehensive post on how you might get the reported problem when using layers and how the layer attributes in Gimp 2.10 will be the problem only to find
Not the layers, it is a single layer (I think) in normal mode and brush in darken mode which is different between Gimp 2.8 and Gimp 2.10
Solution as my previous post, put the brush in legacy mode.
Posts: 117
Threads: 23
Joined: May 2017
Reputation:
7
Operating system(s):
- Windows (Vista and later)
Gimp version: 2.10
09-14-2018, 09:53 AM
(This post was last modified: 09-14-2018, 10:13 AM by carmen.)
(09-14-2018, 09:45 AM)Ofnuts Wrote: Works for me:
To clear possible misunderstandings:
- On the top layer, you can paint everywhere, the image below doesn't act as a selection mask
- The top layer applies to the composition of all layers below it, not just to the layer below.
- If you want to apply the effect just on the layer below, you use a layer group.
Without a layer group:
With a layer group:
Otherwise, make a screenshot of your layer stack (and indicate the layer modes by renaming the layers)
(09-14-2018, 09:53 AM)rich2005 Wrote: Sorry guys, my fault over enthusiastic editing of everything quoted over a one line reply.
I was peed off after making a comprehensive post on how you might get the reported problem when using layers and how the layer attributes in Gimp 2.10 will be the problem only to find
Not the layers, it is a single layer (I think) in normal mode and brush in darken mode which is different between Gimp 2.8 and Gimp 2.10
Solution as my previous post, put the brush in legacy mode.
This worked like a charm.
Thank you very much!
QUERY: Are other differences worth noting between normal mode and legacy mode?
I am now editing some old .xcf files, and they open with all the layers in legacy mode, whether it be normal, overlay, saturation... So far, I see no change by switching to the new mode--but my eyesight may easily be at fault. Am I missing something?
Thanks.
Posts: 6,342
Threads: 274
Joined: Oct 2016
Reputation:
564
Operating system(s):
Gimp version: 2.10
What worked like a charm?
|
